Optoma Technology Home Theater Screen Graywolf II User Manual

 
N0.2  
To reduce the risk of electric shock,do not disassemble this  
appliance,only a qualifid service technician may service or  
repair motorized screen.Incorrect reassemble can cause  
electric shock when the motorized screen is used.  
Only use accessory attachment recommended by the  
manufacturer.Use of non-manufacturer recommended acces-  
sory attachments,may viod the screens warranty and release  
Panoview of all liability.  
Basic electrical safety precautions should always be observed.  
In the event,the above mentioned safety precautions are not  
observed.The warranty may be viod and Panoview released of  
all liability.  
 
NO.3  
Thank you for choosing Panoview screens. All screens  
have passed the strict quality inspection before delivery.  
Read this manual carefully to ensure proper usage.  
Important Attention: the installation of the screen,  
the electric wire connection, the setting of the limit  
switches must be made by a trained engineer only.  
SWITCH BOX  
PLUG  
SWITCH JACK  
12V TRIGGER  
Motorized screen with IR remote control, switch control & 12v trigger port  
 
N0.4  
Technical data:  
Input Voltage: 110VAC/60HZ  
Output Voltage: 3A  
Fuse: 1A  
IR Remote Control Distance: ≤8m, 15°Horizontal  
12V Trigger Jack: OD3.4xID1.3  
12V Trigger Signal: Voltage:7---11VAC or 8---16VDC,  
Current: ≥2mA  
IR Handset: 1pc  
Switch control: 1pc  
Unpack screen carefully, be sure screen is in good condition,  
and check that all accessories are included inside carton.  
Care in mounting and care in correct operation will mean a long  
and satisfactory life for your Panoview screen. Locate the screen  
where the audience can best see it and where other furnishings in  
the room permit.  
Check that voltage and frequency marked on screen is in  
accordance with local power utility. It is suggested only to use  
screen indoor under normal temperature and humidity conditions.  
 
NO.5  
Remove two pulling locks on the bottom slat bar after the case  
has been installed.  
Install screen brackets onto ceiling or wall with appropriate  
hardware.  
Anchor screen onto bracket as shown in above figure below.  
MOUNT SCREEN TO WALL  
MOUNT SCREEN TO CEILING  
 
N0.6  
ELECTRIC CONNECTION  
Internal wiring has been completed at the factory.No addi-  
tional wiring is necessary.  
Note:all wiring related to the screen,may only  
be serviced by a manufacturer approved trained  
electrical technician.Tampering with electrical  
wiring may void warranty and release Panoview  
of liability.  
 
NO.7  
OPERATING INSTRUCTION:  
Plug in power supply.  
For Switch control: Plug in Switch into switch jack. Press  
button to Up position, screen goes up. Press button to stop  
position, screen stops. Press button to down position,  
screen goes down.  
For IR Remote: Direct the handset to IR window on  
screen housing. Press the Up/Stop/Down button on the  
hand set, screen goes Up/Stop/Down accordingly.  
 
N0.8  
For 12V trigger: Input 12V trigger signal, screen goes  
down. Stop this signal, screen goes up.  
Electric lock: Press the Up & Down buttons on the IR  
handset together, then all Up & Down buttons on the switch  
and IR handset will be locked. To be unlocked press Stop  
button on the IR handset again or unplug the power supply  
and plug in again.  
Keeping the screen rolled in its protective case when not  
in use. Always examine both front and back of surface  
before re-rolling into case to make certain screen is free of  
dust, dirt or other foreign matter.  
 
 

Moxa Technologies Network Card VPort 2140 User Manual
Nesco Electric Steamer ST 25 User Manual
NordicTrack Home Gym NTHK99901 User Manual
OEM Systems Speaker AP 525 LCRS User Manual
Olympus Battery Charger ET CK30 User Manual
Omega Engineering Power Supply DRN PS 750 User Manual
Panasonic Blood Pressure Monitor EW3109 User Manual
Panasonic Fax Machine KX FL501E User Manual
Panasonic Intercom System KX TD161 User Manual
Paradyne Network Router Hotwiret 7986 User Manual